Random Noise

cat /dev/random >> /dev/dsp

Asus G1S CPU, GPU and Arctic Silver 5

with 6 comments

My laptop usually got very hot and CPU and GPU idle temperatures were in the range of ~75C and ~80C respectively. Its about eight months I bought my laptop and I finally decided to open it up and apply thermal paste to both CPU and GPU.

Getting to the CPU was fairly simple just remove 2+4 screws and apply the thermal paste.

But, getting to the GPU was real pain. So, I decided to write a post to describe it in simple steps and gotchas that I discovered.

Disclaimer: Opening and applying thermal paste to CPU or GPU will void your laptop’s warranty! Author assumes absolutely no liability for these opinions nor for any damages that may result from reading and/or implementing following steps.

Before starting anything, unplug the power 🙂 and remove the battery.

1. Remove the keyboard. For this remove the two screws that are labeled ‘K’ from the under side of the laptop, then using a small flat(slotted) screw driver, un-clip three plastic holders at the top edge of the keyboard . Then tilt it over and unplug two flat cables and one connector with wires grouped together.

2. Then remove the covers of the ram and the hard drive compartment. Carefully remove the rams modules and hard drive and keep it a side. If you haven’t removed CPU compartment cover do it now.
* In the CPU compartment, there is a screw hidden just between the heat sink exhaust and the edge of the laptop. The is covered by the aluminum foil so you have to peel it to remove it.
* Also don’t forget to remove a screw just beneath the hard drive!

3. Remove 3-4 tiny steel screws from the battery compartment. Then remove the rest of the screws from the laptop base. Also remove six screws from the under side of the hinges. Two hinge covers will come off.

4. Remove screws from backside and remove the lid covering the LCD cables. Carefully remove two screws under this lid. Then unplug the two connectors.

5. Tilt screen to the max and remove two long screws that hold the LCD panel in the grooves. Carefully remove the LCD panel and keep it aside.

6. Now slowly lift the upper cover. It should come off w/o problem. You’ll get a first look at the motherboard. But you still don’t see the GPU!!!

7. You have to remove couple more screws and unplug speaker cables and the DVD drive. And volia! you can lift the motherboard and turn it over. And there you’ll see the other heat sink.

8. Go ahead and remove the screws from the GPU heat sink, unplug the fan power connector and carefully detach the heatsink. You’ll see that the underside of the GPU heat sink has a thin aluminum foil that according to me prevents thermal paste short circuiting the connectors on the GPU. There is another reason for doing it this way. During laptop assembly the person gets hardly few minutes to apply the paste and set the heatsink, it is easy to just use the foil to cover the die and apply paste and slap the sink on to it – quick and dirty huh? But as I told earlier it does prevents thermal paste spreading over the GPU circuitry around the die!

9. Remove the foil and the thermal paste. Observe how excessive paste was used! I used a plastic card to get rid of it and finally cleaned it up with some 90% isopropyl alcohol (picked it from local Wallgreens for $2) and cotton swabs. The copper heat sink was now smooth and clean like a mirror. The die should be clean as new – but just to make sure clean it as well using a new cotton swab and alcohol.

Advertisements

Written by Vivek Unune

June 21, 2008 at 4:29 am

Posted in G1S, Hardware

Tagged with , , , ,

6 Responses

Subscribe to comments with RSS.

  1. i applied arctic mx-3 to both cpu and graphics card,
    Idle :CPU went down from 75 to 55, GPU went down from 67 to 64.
    The real difference is when cpu and gpu is under heavy load cpu wonders around 77~79. and GPU is about the same as Cpu, (before applying i remember cpu seeing 90)
    All temperatures are degrees celcius

    Vagabondos

    March 16, 2010 at 6:19 am

    • That’s an improvement! It’s beeen a while I had modded my laptop.

      Vivek Unune

      March 16, 2010 at 1:50 pm

  2. have you ever considered, cutting a small hole at the bottom right below the GPU and just attaching a heatsink with some sort of a permanent paste to the top of GPU heatpipe? This way the air going to the copper fins of CPU will be cooler and the heat transfer will be more, therefore a happy CPU.
    Also, no air should enter from the heatsink so the air passing through from harddrive and RAMs not affected?
    what do you say? is that a good idea?

    Vagabondos

    May 13, 2010 at 8:21 pm

    • Funny that you ask about this. I almost cut a hole just above GPU last week. Just recently the GPU gave up on me. I did try to reflow it and it worked for a day, but died again. It needs re-balling they say.

      Vivek Unune

      May 13, 2010 at 8:26 pm

  3. Thanks for the tutorial on this. Tore down my G1S and cleaned/resilvered the cpu/gpu. I used arctic silver 5, and it already runs cooler. I didn’t have actual temps, but the fan was on all the time, and now it hardly comes on at at all unless the gpu is pushed. Whole process took 4 hours, but I watched a movie with my wife for part of it, LOL. Realistically, it’s a 3 hour job. I’m not an expert, but not a novice either. Definitely worth the time you spend, and breathe life back into an older laptop. Thanks again for this,

    Chris Richardson

    June 27, 2010 at 8:38 am

    • You are welcome Chris.

      Vivek Unune

      June 27, 2010 at 5:47 pm


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: